Request a Quote (337) 573-4406 sales@patriotfts.com
Pair of flanged stainless steel pump connectors

Home / Products / Pump Connectors / Flexible Pump Connectors

Flexible Pump Connectors Pump connectors that isolate vibration.

Short braided stainless connectors that isolate vibration and noise at pumps, compressors and skids and take up minor misalignment, built and pressure tested in Youngsville, Louisiana.

2–14"Flanged connector sizes
1/4–4"Threaded MNPT sizes
321 / 304LStandard hose and braid
MTRsTest reports and MTRs on request

What a pump connector does

A pump connector is a short braided metal hose assembly installed at the pump suction and discharge. It absorbs vibration so it is not carried into the piping, and accommodates small amounts of lateral movement and minor misalignment. Our standard connectors use 321 stainless hose with a 304L stainless braid.

Flanged pump connectors

2"–14", 321 SS hose, 304L braid, 150# carbon-steel plate flanges.

Nominal sizeOverall length
2"–4"9"
5"–6"11"
8"12"
10"13"
12"–14"14"
150# is the flange class, not the assembly rating. The working pressure of the assembly depends on the hose, braid, size and temperature. Confirm it on the quote; see the pressure rating chart.

Threaded pump connectors

VersionSizesLengths
Carbon steel MNPT1/4"–4"1/4–3/8": 6"; 1/2": 6-1/2"; 3/4": 7"; 1": 8"; 1-1/4": 8-1/2"; 1-1/2": 9"; 2": 10-1/2"; 2-1/2": 12"; 3": 14"; 4": 16". Also 12" for 1/2–2".
304 SS MNPT1/4"–4"12", 24" or 36"
316 SS MNPT1/2"–2"12"; 316L hose with 304L braid

Carbon steel threaded connectors use 321 hose and 304L braid. The 316 version is not an all-316 assembly; ask if you need 316 braid. Common custom sizes are 2", 2-1/2", 3", 4" and 6".

What a pump connector doesn't do

  • No axial movement. Pump connectors are not designed for axial compression or extension. That is the job of a metal expansion joint or a flexible loop.
  • No torsion. Twisting the hose shortens its life sharply.
  • Not a fix for bad alignment. Flexible connectors are not a substitute for correct piping alignment and support.

Installation tips

  1. Choose the right length. Braided hose extends roughly 1–2% under pressure; select a length that suits the installed gap without forcing it.
  2. Don't compress or stretch to fit. Install at its natural length, with flexing in one plane.
  3. Prevent twist. On threaded connectors, wrench only on the hex flats and use a backup wrench on the mating hex.
  4. Anchor and support the piping. Pipe weight must not hang on the connector.
  5. Check before covering. Look for leaks and make sure the hose won't rub on anything.

Frequently asked questions

Can a pump connector take thermal expansion?
Not axial expansion. Pump connectors handle vibration, small lateral offsets and minor misalignment. Use an expansion joint or flexible loop for axial growth.
Is a 150# flanged connector rated for 150 psi?
Not necessarily. 150# is the flange class. The assembly rating depends on hose, braid, size and temperature and is confirmed on the quote.
Do you provide MTRs?
Yes, test reports and MTRs are available on request.
Why do pump connectors fail early?
Common causes are axial compression or extension, torsion during installation, excessive misalignment, and unsupported piping. See the installation tips above.

Need it fast?

Call our on-call team any time, day or night, or send your specs online.

(337) 573-4406 Request a Quotesales@patriotfts.com
Designed. Fabricated. Tested. Delivered.  |  Built for performance. Built to last.