
Home / Tech Reference / Flow Velocity Calculator
Flow Velocity and Pressure Drop Keep the flow inside the limit.
Check liquid or gas velocity in corrugated metal hose against the published limits for straight and bent hose, estimate pressure drop and see the smallest size that works. Free, no login.
Patriot FTS Flow Velocity Calculator
Result
Velocity against the limit
Installed configuration
Compare hose sizes
Same flow and length in each size. Green rows are inside the velocity limit for this configuration.
Results are preliminary engineering estimates from catalog data and published industry formulas. Patriot FTS reviews every request and confirms hose construction, live length, ratings and movement capacity on the quote.
How the flow calculator works
Corrugated metal hose has two flow limits that a smooth pipe does not. Fast flow can set the corrugations into resonant vibration and crack the hose quickly, and the corrugations add friction, so a long hose run loses more pressure than the same length of pipe. The calculator checks both.
- Velocity. Flow divided by the bore area at the nominal size. Gas flow in SCFM is first converted to actual flow at your inlet pressure and temperature.
- Velocity limit. The maximum recommended velocity for unlined hose, published across the metal hose industry, falls as the hose is bent: 150 ft/s gas and 75 ft/s liquid in a straight braided hose, down to 38 and 19 ft/s in a 180° bend. Unbraided hose limits are lower.
- Pressure drop. The Darcy-Weisbach equation for clean steel pipe of the same bore, with the Swamee-Jain friction factor, then multiplied by three. A drop of about three times that of comparable steel pipe is the broad rule of thumb published across the metal hose industry.
- Compare sizes. The table repeats the check for each size so you can see the smallest hose that stays inside the limit.
v (ft/s) = 0.4085 × gpm ÷ d² (d in inches)
ACFM = SCFM × (14.696 ÷ Pabs) × (TR ÷ 519.67)
ΔPhose ≈ 3 × f × (L ÷ D) × ρv² ÷ 2gc
| Configuration | Braided gas | Braided liquid | Unbraided gas | Unbraided liquid |
|---|---|---|---|---|
| Straight | 150 ft/s | 75 ft/s | 100 ft/s | 50 ft/s |
| 45° bend | 115 ft/s | 60 ft/s | 75 ft/s | 40 ft/s |
| 90° bend | 75 ft/s | 40 ft/s | 50 ft/s | 25 ft/s |
| 180° bend | 38 ft/s | 19 ft/s | 25 ft/s | 12 ft/s |
When the velocity is over the limit, the usual fixes are an interlocked metal liner inside the corrugated hose, or a larger hose with reducers at each end. The calculator uses the nominal size as the bore; the actual bore varies with the corrugation profile and any liner. Pressure drop for gas is an incompressible estimate and is flagged when the drop is a large share of the inlet pressure. Hose size, liner and ratings are confirmed by Patriot FTS at quote.
Frequently asked questions
What is the maximum flow velocity in a metal hose?
Why does flow velocity matter for corrugated hose?
How much more pressure drop does a metal hose have than pipe?
Does the calculator work for gas?
Which hose bore does the calculator use?
Related tools and guides
- Metal Hose Selector
- Live Length and Bend Radius Calculator
- Expansion Loop Sizer
- Assembly Rating Checker
- Hose Quote List Builder
- Spec Sheet Builder
- Installation Checker
- Inspection and Retest Planner
- Media Compatibility Checker
- Pump Connector Sizer
- Flex Service Screening
- Fitting and Connection Finder
- Overall Length Calculator
- Saturated Steam Calculator
- Unit Converter
- Braid Burst Calculator
- Water Hammer Calculator
- Expansion Joint Quote Builder
- Metal hose pressure rating chart
- Metal hose installation and bend radius guide
Need it fast?
Call our on-call team any time, day or night, or send your specs online.
(337) 573-4406 Request a Quotesales@patriotfts.com