Request a Quote (337) 573-4406 sales@patriotfts.com
Stainless steel flexible U-loops built by Patriot FTS in Louisiana

Home / Tech Reference / Expansion Loop Sizer

Expansion Loop Sizer Plan for movement.

Estimate pipe growth and other movement between anchors and get a preliminary flexible U-loop, V-loop or dog-leg size you can draw or send to Patriot FTS for a quote. Free, no login.

Loop type

Pipe run
Other movement (± each axis)

Seismic, settlement or equipment movement from the engineer of record, entered as ± values.

Loop hose

Patriot FTS Expansion Loop Sizer

Result

Movement by direction

Totals are the full range of travel. ± entries count twice.

U-loop between anchors

Schematic, not to scale. Shown flat for clarity. Loops work in any orientation around the pipe axis; most are installed horizontally.

Draw this U-loop

Results are preliminary engineering estimates from catalog data and published industry formulas. Patriot FTS reviews every request and confirms hose construction, live length, ratings and movement capacity on the quote.

How the expansion loop sizer works

  1. Pick the loop type. U-loops and V-loops go in a straight run. Dog legs go at a corner where two runs meet.
  2. Thermal movement. The pipe between two anchors grows when it heats and shrinks when it cools.
  3. Other movement. Seismic, settlement and equipment movement are added in each direction.
  4. Preliminary leg length. Each hose leg is sized as if it takes its movement as lateral offset, using the dynamic minimum bend radius. On a dog leg, each leg takes the other run’s growth.
  5. Send it. Open the loop in the drawing generator or email the inputs to Patriot FTS. We confirm loop dimensions and movement capacity on the quote.

Method

ΔL = α × L × ΔT
Growth = α × L × (Tmax − Tinstall)
Contraction = α × L × (Tinstall − Tmin)
Resultant T = √(X² + Y² + Z²)
Leg live length = √(6RT + T²), R = dynamic MBR

Coefficients: carbon steel 6.5, 304 stainless 9.6 and copper 9.3 ×10-6 in/in/°F, the same values used in our expansion loop sizing guide. U-loop height is estimated as the leg live length plus a long-radius 180° return (1.5 × nominal size) plus the end fitting allowance you enter. V-loop leg length L, measured from the 45° end elbow to the 90° elbow at the point, adds the elbow takeouts to the leg live length; depth from the pipe centerline is L × 0.707. Dog-leg A and B add the 90° elbow radius and the end fitting allowance to each leg.

This is a deliberately conservative screening estimate, not a loop design. Flexible loop movement capacity depends on the hose construction, the loop geometry and the direction of each movement, and Patriot FTS sets the final dimensions during application review. Your piping engineer sets anchor and guide locations and loads.

See also the flexible U-loop page and the FTS-TD-106 expansion loop sizing data sheet.

Frequently asked questions

Is the loop size from this tool final?
No. It is a preliminary estimate to help you plan space and request a quote. Patriot FTS confirms loop dimensions, construction and movement capacity during application review.
Why does the tool use the dynamic bend radius?
It is the conservative choice. Thermal cycles, startups and shutdowns flex the loop many times over its life, so sizing the legs to the constant-flexing radius leaves margin.
How do I enter seismic movement?
Enter the ± value for each axis as given by the engineer of record. The tool doubles it to get the total range in that direction and combines all three axes.
Which loop type should I choose?
A U-loop or V-loop goes in a straight pipe run, and the pipe stays on one line through the loop. A U-loop has two parallel legs, a 180° return and 90° elbows at the ends. A V-loop has two legs at 45°, a 90° elbow at the point and 45° elbows at the ends, so it needs less depth from the pipe but more length along it. A dog leg goes at a corner where two runs meet at 90°. Patriot FTS can recommend the type during review.
Where should the loop go?
Anywhere between two anchors, as long as the return or elbow at the end of the legs is free to move. Guides keep the pipe moving toward the loop. Support the return or elbow with a hanger that lets it travel. Loops can be installed in any orientation around the pipe axis; most are installed horizontally.
What if my pipe material is not listed?
Choose Other and enter the expansion coefficient for your material in ×10-6 in/in/°F.

Related tools and guides

Need it fast?

Call our on-call team any time, day or night, or send your specs online.

(337) 573-4406 Request a Quotesales@patriotfts.com
Designed. Fabricated. Tested. Delivered.  |  Built for performance. Built to last.