How to read this chart
Each value is the published maximum working pressure in PSIG at 70°F for corrugated stainless hose with braid. Ratings depend on three things:
- Series. The corrugation profile and wall. P3 is flexible and lightweight; 800 and 900 are heavier wall; 1400 is extreme pressure.
- Size. Larger nominal IDs carry lower pressure.
- Braid layers. A second braid layer (2B) raises working pressure substantially over a single braid (1B).
Published ratings use a minimum 4:1 safety factor. They are hose ratings only. A complete assembly is limited by its lowest-rated component and by temperature, so check the fitting ratings and assembly MAWP sections before you choose.
P3 and P4 series
P3 is the flexible, lightweight series. P4 is a heavier-wall alternative. PSIG at 70°F.
| Nom. ID | P3 1B | P3 2B | P4 1B | P4 2B |
|---|---|---|---|---|
| 1/4" | 2,360 | 2,832 | 2,500 | 3,375 |
| 5/16" | 1,647 | 1,976 | 2,300 | 3,680 |
| 3/8" | 1,639 | 1,967 | 1,680 | 2,700 |
| 1/2" | 1,225 | 1,470 | 1,240 | 1,980 |
| 5/8" | 1,200 | 1,440 | – | – |
| 3/4" | 1,034 | 1,241 | 940 | 1,500 |
| 1" | 796 | 955 | 630 | 1,000 |
| 1-1/4" | 600 | 720 | 575 | 920 |
| 1-1/2" | 557 | 668 | 500 | 800 |
| 2" | 570 | 684 | 532 | 850 |
| 2-1/2" | – | – | 500 | 700 |
| 3" | – | – | 400 | 600 |
| 4" | – | – | 300 | 444 |
700, 800 and 900 series
700 is the broad-use industrial series, 800 is heavy wall and 900 is the higher-pressure option in small sizes. PSIG at 70°F.
| Nom. ID | 700 1B | 700 2B | 800 1B | 800 2B | 900 1B | 900 2B |
|---|---|---|---|---|---|---|
| 1/4" | 2,116 | 3,125 | 2,562 | 4,099 | 2,754 | 4,406 |
| 3/8" | 1,501 | 2,401 | 1,501 | 2,401 | 1,921 | 3,073 |
| 1/2" | 1,075 | 1,720 | 2,194 | 3,510 | 2,194 | 3,510 |
| 3/4" | 792 | 1,267 | 1,311 | 2,098 | 1,994 | 3,192 |
| 1" | 571 | 914 | 1,069 | 1,710 | 1,599 | 2,558 |
| 1-1/4" | 531 | 850 | 1,110 | 1,776 | 1,317 | 2,107 |
| 1-1/2" | 472 | 755 | 868 | 1,388 | 1,062 | 1,698 |
| 2" | 516 | 826 | 810 | 1,296 | 842 | 1,346 |
| 2-1/2" | 387 | 619 | 578 | 925 | – | – |
| 3" | 316 | 506 | 540 | 864 | – | – |
| 3-1/2" | 297 | 475 | – | – | – | – |
| 4" | 232 | 371 | 333 | 533 | – | – |
| 5" | 191 | 306 | – | – | – | – |
| 6" | 165 | 264 | 266 | 425 | – | – |
| 8" | 234 | 374 | 234 | 450 | – | – |
| 10" | 230 | 367 | – | – | – | – |
| 12" | 161 | 257 | – | – | – | – |
1400 series, extreme pressure
Three or four braid layers give the highest listed working pressures. Bend radius in inches, dynamic / static.
| Nom. ID | Braid layers | Working PSIG | Nominal burst | Bend radius |
|---|---|---|---|---|
| 1/2" | 3 | 4,000 | 16,000 | 14 / 7 |
| 3/4" | 3 | 5,000 | 20,000 | 15 / 7.5 |
| 1" | 3 | 4,200 | 16,800 | 16 / 8 |
| 1-1/2" | 3 | 2,750 | 11,000 | 24 / 12 |
| 2" | 3 | 2,180 | 8,720 | 40 / 20 |
| 3" | 3 | 1,250 | 5,000 | 84 / 32 |
| 4" | 4 | 1,250 | 5,000 | 112 / 52 |
P5 series, large-diameter annular hose
Single-braid ratings for 14" through 24" nominal ID. Bend radius in inches, dynamic / static.
| Nom. ID | Braid layers | Working PSIG | Nominal burst | Bend radius |
|---|---|---|---|---|
| 14" | 1 | 150 | 600 | 72.5 / 38.5 |
| 16" | 1 | 110 | 440 | 81 / 44 |
| 18" | 1 | 85 | 340 | 90 / 49.5 |
| 20" | 1 | 65 | 260 | 99 / 55 |
| 22" | 1 | 50 | 200 | 107.5 / 60.5 |
| 24" | 1 | 45 | 180 | 114.5 / 66 |
Hose values: published maximum working pressures at 70°F. A dash means no rating is published for that series and size.
Fitting pressure ratings
The fittings on each end often limit the assembly before the hose does. These are general screening values. We confirm the actual rating of every component on the quote.
ASME Class flanges (psi, ambient)
Ratings drop with temperature; see the flange pressure rating chart for temperature-adjusted values.
| Class | Carbon steel | 304 SS | 316 SS | 304L / 316L SS |
|---|---|---|---|---|
| 150 | 285 | 275 | 275 | 230 |
| 300 | 740 | 720 | 720 | 600 |
| 600 | 1,480 | 1,440 | 1,440 | 1,200 |
| 900 | 2,220 | 2,160 | 2,160 | 1,800 |
| 1500 | 3,705 | 3,600 | 3,600 | 3,000 |
| 2500 | 6,170 | 6,000 | 6,000 | 5,080 |
NPT threaded fittings (psi)
| Size | 316 SS male | 316 SS female | Brass male | Brass female |
|---|---|---|---|---|
| 1/16" | 11,050 | 6,750 | 5,550 | 3,350 |
| 1/8" | 10,050 | 6,550 | 5,050 | 3,250 |
| 1/4" | 8,050 | 6,650 | 4,050 | 3,350 |
| 3/8" | 7,850 | 5,350 | 3,950 | 2,650 |
| 1/2" | 7,750 | 4,950 | 3,850 | 2,450 |
| 3/4" | 7,350 | 4,650 | 3,650 | 2,350 |
| 1" | 5,350 | 4,450 | 2,650 | 2,250 |
| 1-1/4" | 6,000 | 5,000 | 3,000 | 2,500 |
| 1-1/2" | 5,000 | 4,600 | 2,500 | 2,300 |
| 2" | 3,900 | 3,900 | 1,900 | 1,900 |
Carbon steel NPT ratings match the 316 SS values shown.
Cam & groove (psi)
| Size | PSI |
|---|---|
| 1/2" | 150 |
| 3/4" – 2" | 250 |
| 2-1/2" | 150 |
| 3" | 125 |
| 4" | 100 |
| 5" – 6" | 75 |
| 8" | 50 |
JIC 37° flare, SAE J514 (psi)
| Dash | Pipe | PSI |
|---|---|---|
| -2 | 1/8" | 5,000 |
| -4 | 1/8" | 5,000 |
| -6 | 1/4" | 5,000 |
| -8 | 3/8" | 4,000 |
| -10 | 1/2" | 3,000 |
| -12 | 3/4" | 3,000 |
| -16 | 1" | 2,000 |
| -20 | 1-1/4" | 1,150 |
| -24 | 1-1/2" | 1,000 |
| -32 | 2" | 1,000 |
Finding the working pressure of a complete assembly
The maximum allowable working pressure (MAWP) of a hose assembly is the lowest rating among all of its parts and conditions:
- Hose and braid rating from the tables above.
- End fittings, flange class, thread or coupling rating.
- Welds and attachment method.
- Gaskets and clamps.
- Temperature. Ratings fall as temperature rises, so the 70°F values must be derated for hot service.
- Service conditions such as pulsation, vibration, flexing and media.
Send us your working, surge and test pressures with the operating temperature, and we will recommend the series, braid and fittings that meet them.
From the Technical Reference
Tools for this job
Free tools you can use now, then email the result to Patriot FTS for a quote.
Ratings and dimensions are confirmed by Patriot FTS at quote.

