A
- Angular movement
- Rotation of one end of a hose or expansion joint relative to the other, measured in degrees.
- Annular corrugation
- Corrugations formed as separate parallel rings at right angles to the hose axis. The standard for braided pressure hose. See hose types.
- Axial movement
- Compression or extension along the hose or pipe axis. Braided hose should not be loaded axially; expansion joints and loops take it.
B
- Bellows
- The thin-wall corrugated element of a metal expansion joint that flexes to absorb movement.
- Bend radius
- The radius of a bent hose measured to its centerline. Each hose has a minimum static and dynamic value. See the bend radius guide.
- Braid
- Woven wire sleeve over a corrugated hose. It carries the pressure thrust and protects the corrugations.
- Braid angle
- The angle between the braid wires and the hose axis. It sets how much of each wire resists pressure thrust. See the Braid Burst Calculator.
- Braid collar (ferrule)
- The ring at each end where the braid is welded to the hose and fitting.
- Braid coverage
- The share of the hose surface covered by braid wire, as a percentage.
- Burst pressure
- The pressure at which a hose fails. Working pressure is typically one quarter of burst for metal hose.
C
- Carrier
- One of the spools on a braiding machine. Each carrier lays a flat band of several wires.
- Corrugated hose
- Thin-wall metal tube formed with ridges and valleys so it can bend while staying leak tight.
- Cycle life
- The number of flexing cycles a hose survives under stated conditions of bend radius, pressure and travel.
D
- Dog leg
- Two hose legs joined by a 90° elbow, used to take movement in more than one direction. See dog-leg offsets.
- Dynamic service
- Service where the hose flexes repeatedly: thermal cycling, vibration or regular movement.
E
- Effective area
- The area a bellows or hose acts on for pressure thrust, based on its mean diameter rather than the pipe size.
- Expansion joint
- An in-line bellows that absorbs axial, lateral or angular movement in piping. See the Expansion Joint Quote Builder.
- Expansion loop
- A U-, V- or other shaped flexible assembly that absorbs thermal and seismic movement without pressure thrust.
F
- Fill factor
- A measure of how closely braid wires lie together. Coverage is calculated from it.
H
- Helical corrugation
- A single continuous spiral corrugation, like a screw thread. Drains easily but can torque under pressure.
I
- Interlocked hose
- Hose wound from preformed metal strip with folded, unwelded edges. Used for exhaust, dry bulk and as liner or armor.
L
- Lateral offset
- Movement of one end of a hose or joint sideways, perpendicular to its axis, while the ends stay parallel.
- Liner
- An interlocked metal sleeve inside a corrugated hose or expansion joint to smooth the flow and protect against high velocity or abrasion.
- Live length
- The flexible length of hose between the braid collars. See the Live Length Calculator.
M
- Maximum allowable working pressure
- The highest pressure an assembly is rated for at a stated temperature.
N
- Neutral zone
- The straight hose section next to each fitting that should not be bent, so flexing does not concentrate at the collar.
- Nominal size
- The size by which a hose or pipe is named. For metal hose it approximates the inside diameter.
O
- Overall length (OAL)
- The length of a straight hose assembly, face to face of flanges or end to end of fittings. See the Overall Length Calculator.
P
- Pitch
- The distance between corrugations. Close-pitch hose is more flexible.
- Pressure thrust
- The force pressure exerts on the ends of an unrestrained hose or bellows, equal to pressure times effective area.
- Pump connector
- A short braided hose assembly that isolates pump vibration from piping. See pump connectors.
S
- Saturated steam
- Steam at the boiling temperature for its pressure. See the Saturated Steam Calculator.
- Squirm
- Instability where a hose or bellows bows sideways under internal pressure, usually from too little braid support or too much length.
- Static service
- A hose bent once at installation and not flexed afterward.
T
- Takeout
- The rigid length at each end of an assembly: fitting plus braid collar.
- Temperature derating
- Reducing a pressure rating for service above 70°F, using factors for the braid and fitting materials.
- Test pressure
- The pressure an assembly is held at for a hydrostatic or pneumatic test, typically 1.5 times working pressure.
- Tie rods
- Rods across an expansion joint that restrain pressure thrust while allowing lateral movement.
- Torsion
- Twisting of a hose about its own axis. Even small amounts sharply reduce hose life.
- Traveling loop
- A hose installed in a loop so that one end can move a long distance along a path, as on a moving platen.
U
- UNS number
- Unified Numbering System designation for an alloy, such as S31603 for 316L. See the alloy cross-reference.
V
- Velocity limit
- The maximum recommended flow velocity in corrugated hose, beyond which the corrugations can vibrate. See the Flow Velocity Calculator.
W
- Water hammer
- A pressure surge when a moving liquid column is stopped quickly. See the Water Hammer Calculator.
- Working pressure
- The maximum pressure a hose is rated for in normal service, usually at 70°F.
From the Technical Reference
Tools for this job
Free tools you can use now, then email the result to Patriot FTS for a quote.
ToolUnit ConverterPressure, temperature, length, flow and more, plus an NPS to DN lookup
ToolMetal Hose SelectorEnter size, pressure and temperature to see every catalog hose construction that qualifies, lightest first
ToolHose Drawing GeneratorBuild a dimensioned drawing of a straight hose, pump connector, dog leg, U-loop or V-loop with catalog hose ratings, then email it for a quote
ToolSpec Sheet Builder (TD-105)Fill in the TD-105 specification online and get a clean one-page spec sheet to print, save or email
Browse all 62 Tech Reference itemsExplore hose by market in 3D
Ratings and dimensions are confirmed by Patriot FTS at quote.
Frequently asked questions
What is the difference between live length and overall length?
Live length is the flexible hose between the braid collars. Overall length adds the two end takeouts, the fittings and collars, and is measured face to face of flanges or end to end of fittings.
What does the braid do on a metal hose?
The braid carries the pressure thrust that would otherwise stretch the corrugated hose, and protects the corrugations from damage.
What is the difference between static and dynamic bend radius?
Static applies to a hose bent once at installation. Dynamic applies to a hose that flexes in service and is larger, often about twice the static value.

