Request a Quote (337) 573-4406 sales@patriotfts.com
Short threaded braided metal hose assemblies

Home / Products / End Configurations / NPT and JIC Threaded Hose

NPT and JIC Threaded Metal Hose Threaded ends, sealed right.

Braided metal hose with NPT pipe-thread and JIC 37° flare ends for instrumentation, machinery and equipment connections, built and pressure tested in Youngsville, Louisiana.

NPTSeals on tapered threads
JIC 37°Seals on a metal flare
1/4–2"NPT sizes rated below
24/7/365On-call service and emergency support

NPT pipe-thread ends

NPT (National Pipe Taper, ASME B1.20.1) has a 60° thread with a taper of 1 in 16. As the male and female tighten, the threads wedge together and seal on the flanks. Standard NPT needs a thread sealant or PTFE tape suited to the media. The rating tables below cover 316 stainless, carbon steel and brass fittings, and our standard threaded pump connectors run 1/4" through 4" MNPT.

JIC 37° flare ends

JIC fittings (SAE J514) have straight UN/UNF threads and a 37° cone. The seal is metal-to-metal on the flare. The threads only clamp the seats together, so no tape or sealant is used. JIC remakes cleanly and handles vibration well, which is why it is common on hydraulic and machinery connections.

NPT vs JIC

FeatureNPTJIC 37°
ThreadTaperedStraight UN/UNF
Seals onThread flanks37° flare seat
SealantRequiredNone
RemakeThreads wear with repeated assemblyRemakes cleanly
StandardASME B1.20.1SAE J514
They don't mix. NPT and JIC are not interchangeable, and JIC 37° does not seal against 45° SAE flare fittings even where threads look similar. Use a proper adapter or order a mixed-end hose, such as MNPT × JIC.

Pressure ratings

NPT fittings (psi)

SizeSteel MSteel FBrass MBrass F
1/4"8,0506,6504,0503,350
1/2"7,7504,9503,8502,450
3/4"7,3504,6503,6502,350
1"5,3504,4502,6502,250
1-1/2"5,0004,6002,5002,300
2"3,9003,9001,9001,900

JIC 37° flare (psi)

DashPipePSI
-41/8"5,000
-61/4"5,000
-83/8"4,000
-123/4"3,000
-161"2,000
-241-1/2"1,000
-322"1,000

Steel = 316 stainless or carbon steel; M = male, F = female. General screening values from our technical reference. Full tables are on the pressure rating chart. The hose, braid, fitting and weld each have a rating; the lowest one sets the assembly.

Installation

  • Trial-fit threads by hand before wrenching.
  • Wrench only on the hex flats, and hold the mating hex with a second wrench so the hose doesn't twist.
  • Keep sealant out of the flow path, and never put tape on a JIC flare.
  • Don't overtighten NPT. It can crack female ports.

Frequently asked questions

Do JIC fittings need thread sealant?
No. JIC seals metal-to-metal on the 37° flare. The threads only clamp the joint.
Can I connect NPT to JIC?
Not directly. Use an adapter, or order a mixed-end hose such as MNPT × JIC.
Is JIC the same as AN?
Both use a 37° flare and generally mate. AN parts are built to military specifications; industrial hydraulics usually specify JIC per SAE J514.

Sources

Need it fast?

Call our on-call team any time, day or night, or send your specs online.

(337) 573-4406 Request a Quotesales@patriotfts.com
Designed. Fabricated. Tested. Delivered.  |  Built for performance. Built to last.