SAE 100R types
SAE J517 groups hydraulic hose into 100R types by construction. The type tells you the reinforcement, the size range and the pressure band. Working pressure falls as the size goes up, so the ranges below run from the largest size to the smallest.
| SAE type | Construction | ID, in. | Max op. psi |
|---|---|---|---|
| 100R1 | One steel wire braid, rubber cover | 3/16–2 | 575–3,250 |
| 100R2 | Two steel wire braids, rubber cover | 3/16–2 | 1,150–6,000 |
| 100R4 | Wire inserted; suction and return | 3/4–4 | 35–300 |
| 100R5 | One wire braid, textile cover; transportation | 3/16–3-1/16 | 200–3,000 |
| 100R7 | Thermoplastic, fiber braid | 1/8–1 | 1,000–3,000 |
| 100R8 | Thermoplastic, high pressure | 1/8–1 | 2,000–6,000 |
| 100R12 | Four-spiral wire, high impulse | 3/8–2 | 2,500–4,000 |
| 100R13 | Four- and six-spiral wire, high impulse | 3/4–2 | 5,000 |
| 100R15 | Six-spiral wire, ultra-high pressure | 3/8–1-1/2 | 6,000 |
| 100R16 | Compact two-wire braid | 1/4–1-1/4 | 1,800–5,800 |
| 100R17 | Compact, one or two wire braids | 3/16–1 | 3,000 |
| 100R19 | Compact, one or two wire braids | 3/16–1 | 4,000 |
Reference ranges from the published standard. 100R9, 100R10 and 100R11 are no longer part of SAE J517. The full table, with proof, burst and bend radius, is on our products page.
ISO 18752 grades
ISO 18752 sorts hose by performance rather than construction. Each grade sets an impulse test, and the letter after it says standard (S) or compact (C), meaning a smaller outside diameter and a tighter bend radius.
| Grade | Types | Test temperature | Min. impulse cycles |
|---|---|---|---|
| A | AS / AC | 100°C (212°F) | 200,000 |
| B | BS / BC | 100°C (212°F) | 500,000 |
| C | CS / CC | 120°C (250°F) | 500,000 |
| D | DC | 120°C (250°F) | 1,000,000 |
Impulse pressure is 133% of working pressure; classes 350, 420 and 560 in grade C use 120%.
Choosing the hose
The STAMPED checklist covers what decides a hydraulic hose:
- Size. Inside diameter for the flow you need.
- Temperature. Fluid and ambient, at the highest point.
- Application. How the hose is routed, flexed and protected.
- Media. Petroleum, water-based or synthetic fluid.
- Pressure. Working pressure plus surges and spikes.
- Ends. Thread type, size, seal style and orientation.
- Delivery. When and where you need it.
Pulsing and high-cycle circuits are where the spiral-wire types and the higher ISO 18752 grades pay off. For heat or aggressive fluids, 100R14 is a PTFE-lined hose with a stainless braid; see our PTFE hose guide.
How we build it
We cut, skive where required, assemble and crimp in our shop, using hose and fittings matched to each other. Every assembly is pressure tested and tagged before it ships, with test reports and material traceability on request. When a machine is down, call the on-call line any time; see emergency hose fabrication.
What we need
- Hose type or standard
- Size and overall length
- Working pressure
- Fluid and temperature
- Both end fittings and orientation
- Quantity and delivery point
Send the old assembly or a photo of the hose markings and fittings, and we can match it.
From the Technical Reference
Tools for this job
Free tools you can use now, then email the result to Patriot FTS for a quote.
Ratings and dimensions are confirmed by Patriot FTS at quote.

