Request a Quote (337) 573-4406 sales@patriotfts.com
Metal hose assembly with one fixed and one floating flange

Home / Products / Assembly Configurations / Fixed x Floating Flange

Fixed x Floating Flange Flex Hose Assemblies Flange x floating flange, built in Louisiana.

Braided metal hose assemblies with a raised-face flange (fixed) on one end and a floating lap joint flange on the other, 1/2" to 24", fabricated and pressure tested in Youngsville, Louisiana.

1/2"–24"Size range
5,000Max psig at 70°F, catalog
TestedEvery assembly
24/7/365On-call service

What a fixed x floating flange assembly is

One end carries a flange welded in place; the other carries a lap joint flange that rides loose on a stub end. The floating flange rotates to line up with the mating bolt holes, so the hose is never twisted during bolt-up. Torsion is one of the leading causes of early metal hose failure published across the metal hose industry, which is why this is one of the most requested flanged configurations.

Typical uses include pump and vessel nozzles, process piping where bolt holes may not line up, and any flanged run where the hose is replaced periodically. These are illustrative; your media, pressure, temperature and movement decide the build.

Sizes and catalog data

This configuration is offered from 1/2" to 24". The pressure range covers the stainless hose constructions at each size; the assembly is rated at the lowest of the hose, braid and both end fittings at your temperature.

SizeStainless hose, psig at 70°FTightest static bendFlangeFloating flange
1/2"1,075–4,0001.5"Class 150: 3.5" OD, 4 x 1/2"Class 150: 3.5" OD, 4 x 1/2"
3/4"792–5,0001.5"Class 150: 3.88" OD, 4 x 1/2"Class 150: 3.88" OD, 4 x 1/2"
1"571–4,2001.75"Class 150: 4.25" OD, 4 x 1/2"Class 150: 4.25" OD, 4 x 1/2"
1-1/4"531–2,1073.5"Class 150: 4.63" OD, 4 x 1/2"Class 150: 4.63" OD, 4 x 1/2"
1-1/2"472–2,7504"Class 150: 5" OD, 4 x 1/2"Class 150: 5" OD, 4 x 1/2"
2"516–2,1805"Class 150: 6" OD, 4 x 5/8"Class 150: 6" OD, 4 x 5/8"
2-1/2"387–9258"Class 150: 7" OD, 4 x 5/8"Class 150: 7" OD, 4 x 5/8"
3"316–1,2509"Class 150: 7.5" OD, 4 x 5/8"Class 150: 7.5" OD, 4 x 5/8"
3-1/2"297–47510"Class 150: 8.5" OD, 8 x 5/8"Class 150: 8.5" OD, 8 x 5/8"
4"232–1,25013"Class 150: 9" OD, 8 x 5/8"Class 150: 9" OD, 8 x 5/8"
5"191–30618"Class 150: 10" OD, 8 x 3/4"Class 150: 10" OD, 8 x 3/4"
6"165–42519"Class 150: 11" OD, 8 x 3/4"Class 150: 11" OD, 8 x 3/4"
8"234–55020"Class 150: 13.5" OD, 8 x 3/4"Class 150: 13.5" OD, 8 x 3/4"
10"230–36725"Class 150: 16" OD, 12 x 7/8"Class 150: 16" OD, 12 x 7/8"
12"161–25730"Class 150: 19" OD, 12 x 7/8"Class 150: 19" OD, 12 x 7/8"
14"15038.5"Class 150: 21" OD, 12 x 1"Class 150: 21" OD, 12 x 1"
16"11044"Class 150: 23.5" OD, 16 x 1"Class 150: 23.5" OD, 16 x 1"
18"8549.5"Class 150: 25" OD, 16 x 1-1/8"Class 150: 25" OD, 16 x 1-1/8"
20"6555"Class 150: 27.5" OD, 20 x 1-1/8"Class 150: 27.5" OD, 20 x 1-1/8"
22"5060.5"Class 150: 29.5" OD, 20 x 1-1/4"Class 150: 29.5" OD, 20 x 1-1/4"
24"4566"Class 150: 32" OD, 20 x 1-1/4"Class 150: 32" OD, 20 x 1-1/4"

Values are catalog figures published across the metal hose industry, at 70°F unless noted. They are a starting point for selection, not a certification. Ratings and dimensions are confirmed by Patriot FTS at quote.

How overall length is measured

Overall length runs from the raised face of the flange on one end to the face of the stub end on the other. Give the installed gap and we will set the hose live length so the assembly fits without stretching or compressing. The overall length calculator works it out from the end fittings.

Materials

Hose: 316L / 321 stainless, Alloy 625, Alloy C-276, Alloy 400 (Monel), Bronze. End fittings: carbon steel, 304/304L or 316/316L stainless, low-temperature carbon steel (A350 LF2) for flanges, or matched to the hose alloy. Material availability by size is confirmed at quote.

Installation notes

  • Do not twist the hose during installation; use the swivel, union or floating end to make up the last joint.
  • Keep bends within the minimum bend radius and in one plane.
  • Support the piping so its weight does not hang on the hose.
  • See the installation and bend radius guide.

What we need

  • Nominal size and overall length
  • Both end connections and their material
  • Hose alloy, or let us select
  • Media, pressure and temperature
  • Movement or vibration, if any
  • Quantity, testing and documentation

Build this configuration in the hose drawing generator, then use Email to Patriot FTS for a quote, or send your specs. Ratings and dimensions are confirmed by Patriot FTS at quote.

Frequently asked questions

What sizes are available as fixed x floating flange?
1/2" through 24". Ratings and dimensions are confirmed by Patriot FTS at quote.
What pressure is a fixed x floating flange assembly rated for?
Stainless hose at these sizes ranges from 45 to 5,000 psig at 70°F in catalog data. The end fittings and temperature can lower the assembly rating, which we confirm at quote.
How do I measure overall length?
From the raised face of the flange to the face of the stub end.
Is every assembly tested?
Yes. Every assembly is pressure tested before it ships.

Need it fast?

Call our on-call team any time, day or night, or send your specs online.

(337) 573-4406 Request a Quotesales@patriotfts.com
Designed. Fabricated. Tested. Delivered.  |  Built for performance. Built to last.